AC/DC Power Adapter, Can the power supply manufacturer attend noise testing of the board power supply? | Joint Measurement in Combination with Equipment

Yes, we can attend. We support joint testing in which technical staff from our Tokyo headquarters attend noise and Lightning Surge tests combining your equipment with power supplies (AC/DC Power Adapter and board-level power supplies). Testing can be conducted either at your facility or at a third-party laboratory. During testing, we compare different countermeasure components and work with you to identify a configuration that meets the required standards.

What Is Joint Testing?

Joint testing is an evaluation method in which your equipment is combined with a power supply (such as an AC/DC Power Adapter or board-mounted power supply) to measure its immunity to noise and Lightning Surge, while the power supply manufacturer's engineers consider countermeasures on-site.

We attend joint testing both at your testing facilities and at third-party laboratories. Engineers from our Tokyo headquarters will visit the test site.

Joint testing is available not only for AC/DC Power Adapter, but also for board-mounted power supplies (open-frame power supplies) installed in equipment.

Key point: Joint testing helps identify countermeasures when noise standards cannot be met. It is also useful for verifying whether cost-reduction proposals or component changes affect immunity to noise or Lightning Surge.

Even If the Power Supply Passes on Its Own, It May Exceed the Limits When Combined With the Equipment

AC/DC Power Adapter and onboard power supplies may meet noise standards on their own but exceed the limits when connected to equipment. This is because noise characteristics vary depending on cable and wiring layout and equipment configuration. The reasons are explained in "Check EMC and Noise Requirements" under How to Choose an AC/DC Power Adapter.

In one of our past projects, an AC/DC Power Adapter met noise standards on its own but exceeded the limits when combined with the equipment. The customer's and our engineers worked together to investigate countermeasures and identified a solution involving a review of component values. Joint testing is an effective way to check noise levels with the power supply connected to the equipment.


Main Items That Can Be Checked Through Joint Measurements

Through joint measurements conducted to date, we have checked the following items. Testing is performed in accordance with the standards applicable to the customer's equipment (VCCI, CISPR 32, IEC61000-4-5, etc.).

ItemWhat We Check
Conducted Noise (Mains Terminal Disturbance Voltage)This is noise that travels outside the equipment through the power cable. We check how much margin there is relative to the limit.
Radiated Noise (Radiated Disturbance Field Strength)This is noise radiated into the surrounding space from equipment and cables. We also check for changes caused by the placement of power cables and wiring.
Lightning SurgeThis is immunity to momentary high voltages caused by lightning. When components are changed, we check that immunity has not decreased.

Please contact us about other test items as well.


Features of Our Joint Testing Service

Our Technical Staff from the Tokyo Head Office Will Attend the Testing

Our technical staff will visit your testing facility or a third-party laboratory to review the test results on-site. Rather than waiting to receive the results before taking corrective action, we can consider the next steps at the testing site.

We Prepare Measurement Data and Countermeasure Components Before Testing

We measure the noise generated by the power supply alone in advance and bring the data to the test. We also prepare countermeasure components in case the product fails to meet the applicable standards. This allows you to make effective use of the limited testing schedule.

We Replace Components One at a Time and Compare Their Effects

We replace and compare noise-affecting components one at a time, including Transformer, MOSFETs, line filters, and capacitors. After determining which components are effective, we decide on the appropriate countermeasures.

We Share the Results with Development and Manufacturing Sites and Apply Them to Mass Production

We share the results of joint measurements with our development and manufacturing sites and create samples incorporating the countermeasures. When changing components, we also check the impact on mass-production specifications and safety standard certifications (Semi-Customization Workflow).


Collaborative Testing Process

Collaborative testing proceeds as follows.

StepDetails
STEP 1 ConsultationWe discuss the applicable test standards, acceptance criteria, test location, and schedule.
STEP 2 PreparationWe measure noise from the power supply alone and prepare mitigation components.
STEP 3 Collaborative TestingWe perform measurements with the power supply connected to your equipment. If the results do not meet the criteria, we replace components and compare the results.
STEP 4 Implementation of Mitigation MeasuresWe produce a sample incorporating the mitigation measures. You then reevaluate it through your testing process.
STEP 5 Mass ProductionWe incorporate the mitigation measures into the specifications, confirm their impact on safety certification, and then proceed to mass production.

Information to Provide When Consulting Us About Joint Testing

Providing the following information will allow us to prepare for the test in advance.

ItemExample
Test StandardVCCI, CISPR 32, IEC 61000-4-5, etc.
Acceptance CriteriaRequired margin relative to the limit values, number of samples that must meet the criteria, etc.
Test Location and ScheduleYour test facility or a third-party laboratory, and the scheduled test date
Equipment ConfigurationEquipment to which the power supply will be connected or installed, and cable lengths and layout
Power Supply in UseModel number of the AC/DC Power Adapter or onboard power supply (products from other manufacturers are also acceptable), output voltage, and output current

You may consult us even if some items have not yet been determined. Our sales team will work with you while confirming the necessary information.


Joint Testing Case Study

This case study describes how we conducted joint testing with a telecommunications equipment manufacturer to evaluate a cost-reduction proposal for an AC/DC Power Adapter. Because the conducted noise margin did not meet the required standard, we replaced and compared the Transformer, MOSFET, and line filter one at a time. Without fundamentally changing the circuit, we implemented countermeasures by selecting appropriate components and adjusting the PCB layout.

Noise Countermeasure Case Study for an AC/DC Power Adapter for Telecommunications Equipment | Evaluating a Cost-Reduction Proposal Through Joint Testing

For other examples of noise and Lightning Surge countermeasures, see Semi-Custom AC/DC Power Adapter Case Study for Industrial Equipment (Noise Countermeasures) and Enhanced Lightning Surge Immunity (Outdoor Telecommunications Equipment).


Frequently Asked Questions About Joint Testing

Can you attend tests conducted at a third-party laboratory?

Yes, we can. We support joint testing both at your test facility and at third-party laboratories. Please let us know the location of the laboratory and the test schedule.

Can we consult with you if an AC/DC Power Adapter or onboard power supply from another manufacturer fails to meet noise standards?

Yes, you can. We will explore possible solutions, including replacing the existing power supply with one of ours. Please provide the model number of your current power supply and the applicable test standard.

Can joint testing also be used when considering ways to reduce power supply costs?

Yes, it can. Changing components may affect noise performance and resistance to Lightning Surge. Through joint testing, samples incorporating proposed revisions can be evaluated according to your criteria.

Related Pages on Noise Countermeasures

Contact Us About Joint Measurements and Noise Countermeasures